Tongue and groove paneling is a popular way of adding character and beauty to a space. Although there are many methods for installing this type of paneling over drywall, they all require precise measuring and cutting. One common method is to nail panels directly onto furring strips that run vertically down the wall. Another option is to place panels diagonally. This involves cutting a 45° angle at the ends of each panel in order to form the long groove side.
Installation Steps
You must remove all hooks, outlets and nails from walls before hanging wood planks. Also, you'll need to sand any protrusions from the walls. You can use a power drill or large sections of sandpaper and an extension table to accomplish this task.
Determine whether your tongue and groove paneling is nailed to drywall or studs
To check if your tongue and groove wall panels are nailed to drywall, place a pry bar near the corner of the wall where two walls meet. With your hammer, gently tap the pry bar into the seam where the two walls meet. You will need to remove the panel from the wall if it isn't nailed to the drywall using a prybar and pliers.
Determine whether your tongue and groove wall panels are nailed or glued on
Once you're certain that your paneling has been properly nailed to drywall and are satisfied with that, start removing any trim attached to the wall. Ideally, you'll be able to reuse the trim, so try your best not to damage it.
You will need new wood paneling if you are unable to reuse the trim. To determine the number of sheets 4'x8' you will need, measure the wall you are covering. A panel will be needed for every door and window on walls over 8 feet.
Drywall Straightedge Marking
Make sure your wood paneling runs evenly along the drywall surface. Run a straight edge down the wall side-to-side to make sure it is. Look for any areas where the drywall protrudes above or below the wood paneling, especially at corners and over door and window frames. If the drywall bulges, it'll cause your paneling to not lay flat or to stick out excessively.
Use a dust mask to sand the drywall
You should sand any areas where the drywall is protruding when installing tongue and groove panels over drywall. This will make your paneling easier to install and allow for a more uniform installation.
Finish with a Wood Puffin
Once the drywall has been sanded, you can apply a coat wood putty on the walls and paneling to seal any joints between them. You can also stain the paneling with a wood stain to give it a more natural look, but this is a more labor-intensive process than applying a coat of paint.
Drywall Attachment Paneling
You will need a nail set that has rounded heads to attach wood paneling and drywall. These fasteners cost about $4 per package of common 16-penny nails and are available at most hardware retailers. These fasteners are compatible with any kind of wood including plywood and drywall. But if you need to install thicker boards than that, use construction staples instead or pneumatic fasteners.
FAQ
How often should my furnace filter be changed?
The answer will depend on how often your family is going to use your heating system. You may need to change your filter more frequently if the temperature drops and you plan on being away from home during colder months. If you're not often out of your home, however, you may be more able to wait for the filter to change.
A furnace filter can last about three months. This means that you should replace your filters every three months.
You can also consult the manufacturer's recommendations regarding when to change your filters. While some manufacturers recommend replacing your filter once per heating season, others recommend waiting until there is visible dirt buildup.
How much does it cost for a house to be renovated?
Renovations usually cost between $5,000 and $50,000. Most homeowners spend between $10,000-$20,000 on renovations.
Do I have to renovate my entire house?
Why pay someone to do it for you when you can do it yourself?
It doesn't matter how much you love DIY, there are times when you simply cannot do it yourself. There may be too many variables involved for you to control.
For example, if you live in an old home, you might find that the wiring is outdated and you would need to hire a qualified electrician to make sure that your electrical system is safe and reliable.
Also, you should consider that some structural damage may not be possible during renovations.
You may not have the proper tools to complete the job. For example, if your goal is to install a new sink in your kitchen, you will need to purchase a plumber’s snake, which is designed to clear blocked pipes.
Plumbing codes also require that you have a licensed plumber work on your project.
The bottom line is that you need to know exactly what you are capable of doing before you embark on such a big task.
Ask your friends and family for help if you're unsure if the job is possible.
They can offer advice about what to do and where to go for more information.
What should I look for when buying a home?
Before purchasing a new home, make sure that you have enough money saved up to cover closing costs. Refinancing your loan is an option if cash is tight.
How do I select a competent contractor?
When choosing a contractor, ask friends and family members for recommendations. You can also look online for reviews. Check to make sure the contractor has experience with the type of construction you are looking for. Request references and make sure to verify them.
Is it better to finish floors or walls first?
The best way of starting any project is to determine what you want. It is important that you think about how and who you want to use the space. This will help you decide if you should go for flooring or wall coverings.
If you have decided that you want to create an open plan kitchen/living area then you may choose to install flooring first. If you have chosen to make this room private then you could opt for wall coverings instead.
Is it better to remodel an older house than build a brand new one?
There are two options available to you if you're considering building a home. One option is to buy a pre-built home. This type of home is already built and ready to move in to. You can also build your own home. If you choose this option, you will need to hire someone to help you design your dream home.
It all depends on how much you spend designing and planning the home. Because you will likely be doing most of the work yourself, a custom home can require more effort. You also have greater control over the materials and their placement. So, it might be easier to find a contractor who specializes in building custom homes.
A new home can be more costly than a remodelled home. The reason is that you'll need to pay more for the land, as well any improvements. Plus, you'll need to pay for permits and inspections. The price difference between a newly built and remodeled home averages $10,000-$20,000.
Statistics
- According to the National Association of the Remodeling Industry's 2019 remodeling impact report , realtors estimate that homeowners can recover 59% of the cost of a complete kitchen renovation if they sell their home. (bhg.com)
- Design-builders may ask for a down payment of up to 25% or 33% of the job cost, says the NARI. (kiplinger.com)
- They'll usually lend up to 90% of your home's "as-completed" value, but no more than $424,100 in most locales or $636,150 in high-cost areas. (kiplinger.com)
- On jumbo loans of more than $636,150, you'll be able to borrow up to 80% of the home's completed value. (kiplinger.com)
- A final payment of, say, 5% to 10% will be due when the space is livable and usable (your contract probably will say "substantial completion"). (kiplinger.com)
External Links
How To
5 Things to Know Before You Start Your Home Renovation
-
Are you sure that this is something you want to do? If you're planning on embarking on major home improvement projects like renovating your kitchen, bathroom, or building a brand new house, it's certain that you'll need to have some assistance. It's possible to feel overwhelmed by such a large project. It can take up your time and cost you money. You won't reap the benefits. Instead, you can hire someone who knows their stuff to help. You'll be able to save a lot of time and stress while still having a lovely space to call your own.
-
How much should a project cost? This is a common question, but it can make renovations more expensive. It's because you'll most likely be responsible for paying back the majority of the costs. Stick to your budget if you have one! If you don't, you might end up spending a lot of money and not receiving anything.
-
Should I use DIY or hire professionals? - There's no right and wrong answer. We recommend hiring professional tradespeople, however, if you're able to afford them. They'll give you the best advice possible on how to proceed with your particular project. They can install the plumbing correctly and make sure that it is done safely. DIY projects are often a trial-and-error process, so you'll need to learn a lot from your mistakes. There will be many problems along the way.
-
Are you able to afford it? - Don’t underestimate the cost associated with a home renovation. Even if the project seems manageable, it could prove costly and you will need to borrow money. If you are planning on selling your existing property soon after finishing the renovations, it is important to include the cost of selling it in your calculations.
-
Where should I begin? There is no wrong or right place to start when it comes time to choose where to begin. But we suggest you choose something that you enjoy working on. If you enjoy what you do, you will be more motivated to continue working and less likely procrastinate. You should also avoid areas that require extensive maintenance. If you have to deal with dirt and dust, don't try to redecorate the living room.